Logo

Ratooragh Weather Systems

Campbell Scientific 2017-09-25 15:10:00 Pressure 1022mb, Temp 15.6°C, RH 87%, Wind Dir 184° at 6knots, Gusting to 11knots, Rain last 24 hrs = 0.2mm and Davis Vantage Pro 2017/09/25 15:10:00 Pressure 1021mb, Temp 14.3°C, RH 95%, Wind Dir 170° at 6knots, Gusting to 12knots, Rain last 24 hrs = 0.2mm <- Current Weather
Date Time: 2017/09/25 15:08, Turbine Speed: 699 rpm, WindSpeed: 5.10 knts, Input to Solar Tank: 6.17 watts, Input to Buffer Tank: 0.00 watts, Solar Relay: On, Buffer Relay: Off, Relay Override: Off, Solar Tank Temp: 46.00 C, Buffer Tank Temp: 20.77 C, Input to Solar Tank in 24Hrs: 0.03 kW, Input to Buffer Tank in 24Hrs: 0.00 kW, Total Energy Generated in 24Hrs: 0.03 kWatts and Date Time: 2017/09/25 15:10:07, PV Energy: 0.8 kW, Solar Rad. Time: 2017-09-25 15:05:00, Solar Rad.: 196 W/m², Sun Elevation: 27.2°, Total Generated in 24hrs: 16.989 kW <- Wind Turbine & PhotoVoltaic Output
Schull Tides for 2017-09-25 Time in UTC
1st HW 07:20 3.1m, 2nd HW 19:40 3.1m, 1st LW 01:00 0.5m, 2nd LW 13:20 0.5m

Altocumulus and Sea Fog

Altocumulus Lenticularis

Altocumulus Lenticularis

Altocumulus Lenticularis

Altocumulus Lenticularis

Altocumulus

Cirrocumulus with Contrails

Cirrocumulus

Cirrus

Crepuscular Rays

Crepuscular Rays

Cumulonimbus

Cumulonimbus

Cumulonimbus

Squall Line

Double Rainbow

Double Rainbow

Moonset

Sea Mist

The Sea 'Steaming'

Snow Storm

Storm Front, Thailand

Stratus

Altocumulus at Sunrise

Sun Setting

Sunset

Sunset under Stratocumulus

Receive Eumetcast Using Linux

Receiving Eumetcast using Debian 7 in 90 mins

I have been a Linux user for many years. The more I use Windows, the less I like it. With Support for Windows XP finishing this April, and the new DVB S2 reception from Eumetcast coming I decided to start getting rid of Windows by receiving Eumetcast using Linux.

You do NOT need to be an expert in Linux to do this.

Now you may say 90 mins is a bit ambitious, but I did cheat a little. I got a working system up and running in a morning, but decided to start again, so there were no unnecessary programs installed or running on my nice clean Debian box. The fresh install with Eumetcast reception working did only take 90 mins the second time.

I began by looking at the Eumetcast CD. In the Linux directory there is a Readme_first.txt file which lists the supported Linux distros. I am not too familiar with Redhat, Fedora or OpenSuse, and not too keen on Ubuntu. Personally I mainly use Arch Linux and Gentoo Linux. I decided to use Debian Linux which is well known for it's stability, and I was pretty sure would work fine with the Eumetcast software. Debian is now at version 7 so to begin with I setup a very basic installation of Debian 7 using the small netinst image from the website.

In Debian 7 the current kernel version is 3.2, much newer than the 2.4 or 2.6 kernel in Debian 4, so is more likely to have the correct drivers for your motherboard.

My PC is a fairly old 32 bit Pentium M with a 1.7Mhz processor and 1Gb memory and a Gigabit Ethernet Controller on the motherboard connected to my LAN. I added a D-Link Gigabit Ethernet Controller into a PCI slot for the Traffic link to the Ayecka SR1 I had been fortunate to buy at the GEO Symposiom. More on this later. I have two hard drives installed, a small one 80Gb for the operating system and another 160Gb for the Eumetcast received data, which I do NOT plug in until I have the operating system working correctly to avoid accidently installing it on the wrong drive.

This is what I did to Install Debian.

Downloaded the netinst iso from the Debian website http://www.debian.org/distrib/ and burned a CD. Screenshot of Debian Net Install

Booted the PC using the CD , and installed a basic system. The detail of this is here.

My description is not exhaustive. Most of it is very simple, requiring only common sense. You will be working from the command line which can be a bit scary to begin with, but gets easier in time, and very soon you will see the flexibility and power offered by Linux which cannot be matched by Windows.

Apart from the very basic installation I made sure during the install I had the following services installed:

  • 'File Server' which is SAMBA for sharing on a Windows workgroup

  • 'SSH server' to allow logging into the server from another computer using ssh fom a terminal in Linux or using Putty in Windows. In Linux you would type

    ssh USERNAME@DEBIAN_MACHINE_ADDRESS_OR_HOSTNAME

    to log in from another computer. Here is an example logging into my Eumetcast machine using a Terminal from my wife's computer which is running Linux Mint.

    ssh login in a terminalYou can click on this image for a bigger view.

  • 'Standard system utilities' essential on any system.

After the install I also installed the following:

  • 'Vim' the editor which I prefer to the default Nano editor. It is worth learning from the excellent tutorial included with the installation.

  • 'Ssmtp' a simple mail daemon to allow the computer to mail information to you.

  • 'Rsync' to enable syncronising directories both local and remote, and also good for copying files.

  • 'Snmp' for monitoring of this machine using mrtg.

The Network for Ayecka SR1

The Ayecka SR1 is a router and is not installed in the PC. This is excellent! No need to worry about DVB drivers on the PC. The Ayecks SR1, in addition to it's USB/Serial port and 2 Rx ports, has 2 network interfaces, one for Management and one for Traffic. I have the Management interface plugged into my home network and the Traffic interface plugged directly into the D-Link NIC on my PC. You do not need to use a crossover cable, a normal Cat 6 patch cable will do the job. The beauty of this is that traffic can pass uninterupted to the PC, and any PC on the home network can interrogate the management interface.

The NICs on the PC are setup with static IP addresses. For more on this see my site on the Debian Install page.

Now for the Eumetcast bit.

First off you will need your second drive added and formatted. I will not show you how to do this, there is plenty of stuff on the net showing how to use fdisk. I have formated the disc using the reiserfs system because it is meant to be faster than the ext4 filesystem.

create a folder in your home folder

mkdir ~/Eumetcast/received

(In Linux the ~ signifies your home directory as in /home/USERNAME/

Then setup the mount in your /etc/fstab by editing the file and adding a line to add the mount points here is mine. Any line with a # at the front is ignored and can be used for comments.

#Mount point for received files
UUID=3be8f58b-d995-4d07-a9f3-85008a2663de /home/USERNAME/Eumetcast/received reiserfs defaults 0 1

You might as well add the usbfs as well whilst you are at it. This is needed by the EKU setup

# for usb key
usbfs /proc/bus/usb usbfs defaults 0 0

and save the file.

Now your UUID number will be different than mine. you find the UUID as follows

sudo ls -l /dev/disk/by-uuid

and you can copy and paste the long number relating to your partition mounted on /home/USERNAME/Eumetcast/received (it might be /dev/sdb1 ) into the correct place in your /etc/fstab file.

In Linux you can select text in the terminal with the mouse, hold down Shift-Ctl-C to copy text, then place the cursor in the place you want to paste the text and hold down Shift-Ctl-V. Very handy!

now reboot

ssh into the machine again

type

mount

and you should see all your mounts including the /home/USERNAME/Eumetcast/received

Now to setup the RAM Disk. Thanks to Ernst Lobsiger for this

Here is what he suggests >

The kernel boot parameters are only used if your ramdrive is compiled into the kernel. Nowadays this is usually loaded as a module and it's name has changed from rd to brd.

So I use the following line in /etc/modules to load an appropriate RAM drive:

brd rd_nr=1 rd_size=305000 max_part=0

In /etc/recv.ini I have a line:

file_database_size=300000000

That works fine even if in the startup scripts EUMETSAT still uses the name rd.

This next bit should be done after the Tellicast software is installed

When the partition is setup in the tellicast client script /etc/tellicast-client I changed line 149 to add "...... -m 0 ..." so it becomes

/sbin/mkfs -t ext2 -m 0 $RAM_DISK_DEVICE > /dev/null 2>&1

meaning I added "-m 0" to prevent a reservation of 5% root only blocks. If you do not add "-m 0" on your ramdisk 5% will be reserved for root only and if your tc-recv is running as another user than root these reserved blocks will not be accessible for the client and thus be wasted.

>>>>>>

Create directory to mount ramdrive

mkdir ~/ramdrive

you will need to specify this in your recv.ini file for tellicast to mount

Now for File Sharing

SAMBA is used to share the received files across a windows network so David Taylor's software can reach it. Samba is already installed. Edit the config file to share the received files /etc/samba/smb.conf

sudo nano /etc/samba/smb.conf

edit line in [global] section

workgroup = <YOUR_WORKGROUP>

and create a share adding this

[Eumetcast]
comment = Eumetcast Directories
path=/home/USERNAME/Eumetcast
guest ok = yes
browseable = yes
create mask = 0777
directory mask = 0777
force create mode = 777
force directory mode = 777
force security mode = 777
force directory
security mode = 777
read only = no
writable = yes

then start samba

sudo /etc/init.d/samba start

and at bootup

sudo update-rc.d samba enable

then check from a windows machine that you can read and write the share

OK back to the Eumetcast CD

Put it in the CD drive of the receive machine and mount it.

type

sudo mkdir /mnt/cdrom

sudo mount /dev/sr0 /mnt/cdrom

now

mkdir ~/EumetsatCD

This is where 'rsync', which you installed earlier, comes in handy.

copy cd files to ~/EumetsatCD

rsync -avr /mnt/cdrom/Linux ~/EumetsatCD/

the files and folders for a Linux install will be copied onto the PC from the Eumetcast CD.

unmount CD and eject

sudo umount /mnt/cdrom

sudo eject /dev/sr0

then move CD to computer you are sshing from and open the Linux/readme_Installation.txt file. I ignored the DVB section going straight to section 2. Install the EKU support because I am using the Ayecka SR1 router.

Now for the EKU software

You can read the Readme_debian_ubuntu.txt file in the Linux/EKU_software folder and follow the instructions. The commands need to be run as the root user, so to save having to type sudo in front of everything, type

sudo -i

enter your password and you will have a root prompt easily recognised as a # rather than a $ sign.

This is where copy and paste comes in handy. You can copy a command from the readme file and go to the terminal and paste it using Shift-Ctl-V.

Now you need to follow the instructions in the Troubleshooting guide which is in the Generic Folder to fix a couple of problems.

  • (C9) EKU / USB Problems with new Linux distributions

edit /etc/udev/rules.d/20-etoken.rules and add the following 2 lines:

 

ACTION=="add", SUBSYSTEM=="usb", SYSFS{idVendor}=="0529", SYSFS{idProduct}=="0514", RUN="/etc/hotplug/usb/etoken"

ACTION=="remove", SUBSYSTEM=="usb", SYSFS{idVendor}=="0529", SYSFS{idProduct}=="0514", RUN="/etc/hotplug/usb/etoken"

 

However the syntax is incorrect for Debian 7 these lines should read

 

ACTION=="add", SUBSYSTEM=="usb", ATTR{idVendor}=="0529", ATTR{idProduct}=="0514", RUN="/etc/hotplug/usb/etoken"

ACTION=="remove", SUBSYSTEM=="usb", ATTR{idVendor}=="0529", ATTR{idProduct}=="0514", RUN="/etc/hotplug/usb/etoken"

 

  • (C11) Missing symbolic link for etoken libraries

    this file /usr/local/lib/aksifdh.so should be present on the system. Type

    ls /usr/local/lib/aksifdh.so

    to see if it is. If not (most likely) you need the link created, so type

ln -sf /usr/local/lib/aksifdh.so.1.3-15.84 /usr/local/lib/aksifdh.so

to create the soft link.

Then run ldconfig to be on the safe side

ldconfig

then reboot the station.

 

Now for the Tellicast Software

Look at the Readme_Tellicast_Linux.txt in the Linux/Tellicast folder. Goto section 2a and install the package. You will need to be the root user still.

Then you will need to modify the /etc/tellicast-client script to add Ernst's little fix as above.

The contents of the /etc/recv.ini and recv-channels.ini will need to be set according to your own needs. There is plenty about this on David Taylor's site. I have also found Arne van Belle, Rob Alblas and Ernst Lobsiger's sites extremely informative and well worth a visit.

I use the /etc/rc.local file to start the services to make sure they start in the correct order. Add these lines to the file BEFORE exit 0

/etc/init.d/etokend start

/etc/init.d/pcscd start

/etc/init.d/tellicast-client start

and issue these commands

update-rc.d etokend disable

update-rc.d pcscd disable

update-rc.d tellicast-client disable

to remove the scripts from the bootup

With the EKU plugged in you can monitor your Telicast from any browser on the network using http://IPADDRESS_DEBIAN_MACHINE:2517 and look at the license page to see if you have this

host_key_4:   ****-****-****-****

Over on the right side of the page.

I would hope by now you have a trouble free working system.